3.7V Inductor Capacitor ESR Meter Transistor Tester DIY MG328 Multifunction Tester

Based on 0 reviews. - Write a review

$14.03

Ex Tax: $14.03

Stock: In Stock
Model: EB0047235
SKU: EB0047235

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Features:

- The tester uses 3.7V rechargeable lithium battery (battery model: 14500)

- With MINIUSB port,it can power the tester, or charge for the 14500 battery.

- One key measurement operation, auto power off delay. Shutdown current is only 20nA, support for battery operation.

- Automatic detection PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET FET, diodes, two diodes, thyristors, resistors, capacitors, inductors. Automatic detection pin definitions.

- Measuring the current amplification factor (B) of the bipolar transistor and the turn-on voltage of the emitter junction (Uf). Darlington transistor amplification factor can be identified by the high threshold voltage and high current.

- Can detect bipolar transistors and MOSFET's internal protection diodes and displayed on the screen.

- Measuring the threshold voltage and the gate capacitance of the MOSFET.

- Support two resistance measurements, the potential can be measured. If the potentiometer is adjusted to its end, the tester can not distinguish between the middle and the ends of the pin.

- Resistance measurement resolution is 0.1 ohms, the maximum value of 50M ohms measurements.

Capacitance measurement range from 25pf to 100mF (100000 UF). Resolution up to 1 pF, inductance measurement range 0.01MH-20H, otherwise it will appear as a resistor, inductor DC resistance is higher than if Europe 2100 will also be displayed as a resistor.

- It can detect 2UF above capacitor equivalent series resistance (ESR), a resolution of 0.01 ohms. This feature is very important for the detection of the capacitor performance.

- It can display symbols of the two diodes in the right direction, also shows the forward voltage drop.

- LED detection for diode forward voltage drop higher than normal. Dual LEDs detected as double diode. Simultaneous detection of light-emitting diodes will flash.

- Time for each test is about two seconds, only the large capacitance and inductance measurements will take a long time.

Specification:

1. ATmega328 microcontroller.

2. 2x16 character LCD display results.

3. one-button operation, automatic power off.

4. shutdown current of only 20nA, support for battery operation.

5. low-cost version without the crystal, auto power off. 1.05k version of the software ATmega168 or ATmega328 in sleep mode when no measurement to reduce power consumption.

6. Automatic detection PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET, diodes, dual diode, thyristor SCR.

7. automatically detects the pin layout.

8. the threshold voltage and current amplification factor of the emitter junction of the bipolar transistor measurements.

9. Darlington transistor through a high threshold voltage and high-current amplification factor identified.

10. pairs of bipolar transistors, MOSFET protection diode testing.

11. The threshold voltage value 11 and the gate capacitance of a MOSFET is measured.

12. Supports two resistance measurements and symbols show the highest four numbers and units. Both ends of the resistor symbol is shown connected to the tester probes number (1-3). Therefore, the potential can also be measured. If the potentiometer is adjusted to its end, the tester can not distinguish between the middle and the ends of the pin.

Please notice:

1. how to calibrate,

Short three test point, the screen shows into calibration step. When prompted to disconnect the short end,please disconnected three tests points, calibration will continue, plug the canacitance when prompted plug into a capacitance over 100nF between 1 and 3 feet(Please use the nonpolarized capacitors over 100nF),then the program will automatically enter the next step, until the calibration is completed, reboot to complete the correction.

2. when you use the battery first time,please activate the battery.

method 1, short the 2 point on the backside as the picture shows after you install the battery.

method 2,charge the battery after you install the battery.

Package Included:

1 x M328 Transistor Tester LCR Capacitance ESR Meter

1 x Test Clip(not include the battery and USB charging cable)

Shipping Time

After you successfully placed an order at RenhotecIC.com, you will receive a confirmation email with your invoice. Once your order is shipped, you will be emailed with the tracking information of your package. Also, you can choose your preferred shipping method during the checkout process. Kindly advise: please select DHL/FedEx if you need our product urgently.

The timeline of the whole shipping process is shown below:

The total delivery time is calculated from the time your order is successfully placed to the time received. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s), includes preparing your items, performing quality inspections, and packaging for shipment. Normally, the processing time is 1-3 days (Only include Monday to Saturday ) after getting your order.

Shipping time: The time for your item(s) to travel from our warehouse to your destination. The shipping time depends on the shipping method you chose. Please refer to the shipping rate section for details.

Shipping Rates

You could choose the shipping method based on your preference during checkout, different shipping methods will apply different rates and shipping times. Please check the following chart for detail:

Shipping Method Shipping Rates Shipping Times
Flat Shipping (Promotion)
$10 About 5-30 Working Days to Worldwide (Only include Monday to Saturday )
Standard Express（0.5KG starting price listed）
Based On Weights About 5-15 Working Days to Worldwide (Only include Monday to Saturday )
Priority Express （0.5KG starting price listed）
Based On Weights About 3-7 Working Days to Worldwide (Only include Monday to Saturday )

In addition, the transit time depends on where you're located, the shipping method you choose, and where your package comes from. We will keep you informed of any problems here to help you get your order as soon as possible.

If you want to know more information, please contact the customer service by contact form or sales@renhotecic.com. We will settle your problem as soon as possible. Enjoy shopping!

Tags: Transistor